Full doors for 1997 jeep wrangler

A 1997 Jeep Wrangler YJ with the factory doors is a fun car, but chances are you’ll be taking it through some pretty tough terrain. If you’re not careful, hitting a low hanging tree branch is inevitable, and your doors will most likely get mangled in the process. It’s time to upgrade, but finding a replacement pair of Wrangler doors can be difficult.

Full Doors are a great turn-key upgrade to any Wrangler. They replace the factory roll bar and provide the ultimate in security since your doors do not need to be removed to open them. This is especially important when on vacation or traveling in remote areas.

Full doors for 1997 jeep wrangler

You can take the doors off your 1997 Jeep Wrangler if you want to replace the seals and gaskets, or just to clean them. If you’re replacing a damaged door, you may need to take off more than one door to get a good fit.

The front doors are easier to remove than the rear ones. The rear doors have three bolts that hold them in place and require a socket wrench. You only need to loosen the bolts slightly before removing them.

You should always disconnect the negative battery cable before working on your vehicle’s electrical system. This will prevent any accidental discharge of electricity while working on the vehicle, which could cause serious injury or damage to electronic components in your car’s electrical system.

Disconnecting the Negative Battery Cable

1 Locate and disconnect the negative battery cable from its battery post using a wrench. Set it aside so that you don’t accidentally reconnect it later during installation of new parts or removal of old ones (see Resources for more information about locating this cable).

2 Open your hood and locate your battery, which is located near the front of the engine compartment under a plastic cover on top of the engine block (see Resources). Remove this cover with

How to Take the Doors Off a 1997 Jeep Wrangler

1. Open the hood and pull back the plastic covering that covers the fender well. This will expose two bolts holding on each side of the door.

2. Unbolt both sides of the door using a socket wrench.

3. Lift up on one side of the door and slide it forward slightly to free it from its track. It might be necessary to tap gently on the top of the door with a hammer if it does not come off easily at first.

4. Lift up on both sides of the door and remove it from the vehicle completely by sliding it forward and out from under its frame tracks on either side of your vehicle’s body frame rail (the long metal bar that runs down your vehicle’s sides).

The first thing you need to do is loosen the door handle bolts. This will allow you to pull the door panel off.

Next, you need to remove the screws holding the door lock mechanism in place. Then you can pop out the lock mechanism with a flathead screwdriver.

Now remove the door panels by removing all of the clips holding them in place. To do this, you’ll need a small flathead screwdriver and some patience. Once all of the clips are removed, pull off both side panels and then remove the front panel last by removing its three screws (two on top and one at bottom).

You’ll now have access to your speaker wires and other wiring harnesses within your Jeep Wrangler’s doors. To disconnect these wires simply unplug them from their respective connectors located inside each door panel. You can use either needle nose pliers or a flathead screwdriver to gently pry open any connectors that may be stuck or difficult to open up yourself

1. Remove door handles.

2. Remove door lock pins from the inside of the door panel by pulling them out with a flathead screwdriver.

3. Unplug electrical connectors from the door panel and remove screws holding it in place.

4. Pull up on the bottom of the panel to release it from its clips, then lift it off completely and set aside.

5. Remove trim around window crank handle (or break it off if it won’t come loose).

6. Remove screws holding window crank handle in place and remove handle completely (some models have a plastic cover over part of this area that must be removed first).

7. Pull up on glass until it comes loose from top rail, then lift glass out of window frame (some models may require removal of metal clips at each side).

How to Remove the Doors From a 1997 Jeep Wrangler

The Jeep Wrangler is the quintessential “go anywhere” vehicle. It’s meant for rugged terrain and open road adventures, but when you’re in your garage or driveway, you may want to take the doors off for easier access to the interior. The removal process is simple, but there are some things you should know before getting started.

Step 1: Slide Out the Lock Rods

Open the door and pull up on the lock rod. This piece of metal runs along each side of the door at about mid-chest level. Push it in toward the front of the Jeep until there is about 1/4 inch of clearance between it and its corresponding slot on each side of the door frame.

Step 2: Lift Up on Your Handle

Turn your handle until it locks into place, then lift up on it with both hands. The handle will disengage from its latch mechanism and come free from its frame mount on top of your door panel.

Step 3: Take Out Your Door Panel

Remove all six Phillips head screws that hold your door panel in place (three per side). Pull out your panel so that you can see where

The front doors on a 1997 Jeep Wrangler can be removed by following these steps:

1. Remove the door panel by removing the screws and clips that hold it in place.

2. Remove the lock cylinder from the door handle assembly by pulling it out with needle-nose pliers; then remove the clip that holds the lock cylinder to the handle assembly.

3. Use a screwdriver to pry off the plastic trim around each of the inside door handles; then remove all three screws holding each handle in place.

4. Unplug each of the wires from their corresponding connectors at both ends of each wire harness; then pull off all four outer door handle assemblies by removing two nuts on either side using an adjustable wrench or socket wrench set at 90 degrees to loosen them up (you may need to use another tool such as a hammer or mallet).

5. Unplug each of the wires from their corresponding connectors at both ends of each wire harness; then pull off all four outer door handle assemblies by removing two nuts on either side using an adjustable wrench or socket wrench set at 90 degrees to loosen them up (you may need to use another tool such as a hammer or mallet).

The Jeep Wrangler is a car that’s tough to beat. It’s rugged, it’s ready for anything and it’s got a history of being able to take on just about any challenge you throw at it. But that doesn’t mean there aren’t times when you might want to remove the doors from your Jeep Wrangler.

The first thing you’ll need to do is lock your Jeep in park and put the emergency brake on. Now, get under the vehicle and locate the hinge pins in each door. These are basically little metal rods that hold the door in place and connect it to the body of the vehicle. You’ll see them sticking out of the bottom of each door panel near where they meet up with the fender well.

Once you’ve located these pins, use a hammer and nail puller (or anything similar) and pull them out until they come out completely. If they don’t come all the way out by hand then try using pliers or vice grips as needed until they do come out completely. Once they’re out, set them aside somewhere safe so they don’t get lost or damaged while you’re working on your Jeep Wrangler

There are many reasons why you may want to remove your Wrangler’s doors. For example, if you’re doing mechanical work underneath the vehicle, a doorless Jeep is much easier to work on. Or maybe you’re just looking for a little more freedom and fresh air while driving in your Jeep. Whatever the reason, removing your Jeep’s doors is easy enough that even a novice can do it with minimal tools and effort.

Remove the door panels from the door frames using a screwdriver or wrench. If you have an older Wrangler, there may be plastic rivets holding them in place; use a drill or utility knife to remove these as well.

Locate the latch on each door and remove it with a screwdriver or wrench. This will allow you to pull the door out of its frame without having to take off any more pieces of the Jeep’s bodywork.

Put some cardboard or scrap plywood underneath each side of your Jeep so that if you drop something down into the engine compartment (which is where you’ll be working), it won’t get lost forever!

There are a few different ways to take your Jeep Wrangler’s doors off. The most common method is to remove the hand-crank that holds the door closed. This can be done by sliding it out of its slot and lifting it off, or simply moving it forward while lifting up on the door. When you have removed the hand-crank, you will have access to four bolts under the door panel. These bolts can be removed using an Allen wrench and allow for removal of the entire door panel.

Once these bolts are removed, you can pull out the door panel from inside of your Jeep Wrangler. There are clips holding this piece in place so you may need to use some force when pulling it out. Once this is done, you will see two screws located above each hinge on both sides of the door opening. Remove these screws and then lift up on your door panel until it pops loose from its hinges. Once these two screws have been removed, all that remains is removing any electrical wiring or power locks that may still be attached to your Jeep’s original handle mechanism (if applicable).