How to build a deck over concrete porch
How to build a deck over concrete steps, The first step in building a deck over concrete steps is to determine how strong the foundation is. The porch or step foundation can be made of brick or block with cement or stucco as the surface finish.
How to Build a Deck Over Concrete Steps. Building a deck over concrete is a good way to create an instant second floor space on your home. The resulting structure will not only provide you with additional living space, but also add value to your home.
How to build a deck over concrete porch
How to build a deck over concrete steps, composite decking over concrete porch, building a deck over concrete
Deck Building Tips: How to Build a Deck Over Concrete Steps
Building decks on top of concrete steps is one of the most common types of projects we get in our shop. It’s not hard, but it is important that you follow some basic building principles. Here are some tips on how to build a deck over concrete steps:
1) First, lay out your joist headers and footers so that the joists will be on an 8″ centerline. This will allow for proper spacing between the joists so that they don’t interfere with each other when you install them later on.
2) Next, place 2×6 pressure treated beams on top of your footers such that they run perpendicular from one side of the porch to another. These beams should extend past each end of your stairs by about 1-1/2″. You will not attach these beams yet; this is just so you have something solid to attach your ledger board onto later on.
3) Now set up your ledger board so that it spans across both ends of all three beams (i.e., it
Building a deck over concrete steps is a great way to use an underutilized space for outdoor entertaining. In this post, we’re going to show you how to build a deck over concrete steps and give you some tips on how to make sure you get it done right.
Building a deck over concrete steps requires more than just laying down some lumber and putting down a tarp. It’s important that you follow the correct building codes and safety regulations when doing this project so that it can be accessible for everyone in your family for years to come.
For this project, we’ll be using pressure-treated wood because it’s durable, rot-resistant and termite-free. This type of wood will last longer than regular pine or fir boards — especially if you’re planning on building a large deck over concrete steps — but it can also be expensive when compared with other materials like composite or PVC boards.
If you want to save money while still getting high-quality lumber, consider buying pre-cut boards at your local home improvement store instead of buying them raw at the lumberyard or hardware store. These pre-cuts are already cut down into smaller pieces that are easier to move around and fit into your car without taking up too much space inside the
How to Build a Deck Over Concrete Steps
If you want to build a deck over your concrete steps, there are some specific considerations you must take into account. You will need to build the frame for the deck and attach it in such a way that it can support the weight of the deck above.
Steps You’ll Need
In order to build a deck over concrete steps, you’ll need:
Four 2x4s, 8 feet long
Two 2x4s, 6 feet long
Two 2x4s, 4 feet long
If you’re building a deck over concrete, the first step is to frame the deck. To do this, use 2x4s spaced at 16 inches on center, and attach them to the rim joist with 3-inch screws. You can use pressure-treated wood for the framing if you want to keep your deck looking nice for years or use treated pine or hemlock boards if you don’t mind seeing them rot in a few seasons. For this project, we used pressure-treated pine because it’s inexpensive and easy to find at your local home improvement store.
Once the framing is done, cut 2x6s into sections that are long enough to span between two joists and then screw them into place between each joist using construction adhesive and 1 5/8-inch screws. Make sure that these don’t stick out past the outer edge of your decking boards by more than 1/4 inch (6mm).
Now it’s time to install your deck boards onto these beams. Start at one end of your new decking and snap chalk lines every 4 feet (1.2 meters). Then cut along those lines with a circular saw so that each board fits snugly between joists without any gaps or spaces in between them.
Once
Building a deck over concrete steps is not as difficult as you might think. This article will show you how to build a deck over concrete steps in just a few easy steps.
A deck can be an attractive and functional addition to any home. However, if you want your deck to be safe, it must be built properly on solid ground. The most common mistake made when building decks is not providing enough support for the structure. If the ground beneath it is not strong enough, the deck will sag or crack over time.
The first step in building a deck over concrete steps is to get the right tools and materials together. You will need:
2x6s or 4x4s planks (the size of your choice)
Lumber clamps (1 per plank)
Cordless drill with bits (1/8″ bit)
Hammer (1)
Mason’s string and stakes (1 set)
A composite decking over concrete porch is a good choice for homeowners who want to build a deck without damaging the existing concrete surface. Composite decking is made of recycled materials, such as plastic and wood fibers. It is also more durable than traditional wood decks.
Composite Decking Basics
The basic steps in installing a composite deck are:
Lay down the decking boards on the ground in their desired pattern. Mark the locations of any gaps between boards with chalk or paint.
Align the ends of each board with those of its neighbors and nail them together. If you’ll be using screws instead of nails, make sure that they’re long enough to penetrate through both layers of composite material. If your board has a tongue-and-groove edge, place it against the board below it so that both edges fit together tightly when you lay them side by side. Nail or screw these boards together at several spots along each joint until they’re firmly attached to one another. Do not skip this step; skipping it can cause problems later on when you try to install railings or stairs on top of your decking system.
Continue nailing or screwing boards together until you have completed one row of boards across your patio area. Then repeat these steps
A concrete porch is a great place to build a deck. The steps are already there and the ground may be more level than your yard.
If you have a concrete porch, you can follow these steps to build a deck over it.
Step 1: Prepare the Perimeter
Dig out the dirt around your existing concrete steps and remove any grass or weeds that have grown in between them. Fill in this area with gravel, sand and cement mix to make sure that there is no moisture underneath the decking boards.
Step 2: Build Your Frame
Build your frame using pressure-treated lumber. You’ll need six 2″ x 8″ boards for each side plus two more for each step. Cut these boards according to their lengths needed and nail them together with galvanized nails at every joint. Make sure that all surfaces are smooth so they don’t splinter or scratch when people walk on them with bare feet or shoes with open backs (like flip-flops). Also, be sure to use screws instead of nails whenever possible because screws don’t leave holes in the wood that could harbor insects or rot over time.
Step 3: Attach Your Decking Boards
Set one end of each board against one side
Building a deck over concrete steps is not difficult. You can build the deck from scratch, but if your steps are sturdy and level, you might be able to save some time and money by simply attaching the decking to them. If you do so, make sure that the surface of your concrete is as smooth as possible with no cracks or other defects.
Before you install your decking over concrete steps, make sure that you have plenty of light available for the task. Working in the dark can lead to mistakes that might cause permanent damage to your decking or make it unsafe for use.
1. Measure and mark where each step will be on the ground using masking tape and string. The measurements should allow at least 3 inches of space between each step so there is room for people’s feet as they walk up and down them. Make sure there’s enough room between each step so that one person won’t be stepping on another person’s foot when they’re coming down their own steps at the same time.
Building a deck over concrete steps is not difficult and most homeowners can do the job themselves. Here are the steps to follow:
1. Remove the existing steps by cutting through the nails with a reciprocating saw and prying them up with a crowbar.
2. Dig down about 6 inches on each side of the stairway and fill in with crushed stone or gravel. This will help keep water from seeping into your home when it rains, as well as provide drainage for any runoff.
3. Mix together cement and sand according to package instructions and pour into holes you’ve dug for footings (the part of your deck that sits directly on top of your concrete steps). Let dry overnight before continuing work on your project.
4. Place pressure-treated 2x10s (or larger) horizontally over your concrete steps with 2x6s nailed between them every 3 feet (2x4s can be used if you’re doing this yourself). You may need to adjust these measurements depending on how high or low they need to be built in order to match your existing porch height (decking boards come in different heights).
5. Attach 2x6s vertically along outer edges of horizontal boards using
Step 1: Prep the Concrete
Remove any weeds, grass or debris from the concrete. Clean the surface with a power washer and let it dry completely.
Step 2: Run Underlayment Tape
If you’re building a deck over an existing concrete porch, you’ll need to run underlayment tape over the concrete before applying the decking boards. The tape will help keep moisture out of the concrete, which can cause it to crack or peel. You can purchase precut underlayment tape or measure your own strips and cut them with a utility knife.
Step 3: Install Joist
The joists will give your deck its structural integrity and support the weight of the people who use it. Use 2x6s for joists that span 12 feet or less, and use 2x8s for longer spans. If you have gaps between joists that are more than one inch wide, fill them with a caulking compound made especially for this purpose—once dried, it becomes almost invisible and prevents water from getting underneath your decking boards. After installing joists, use a level on top of each one to make sure they’re all straight before proceeding further in your project.