How to build a sluice box out of wood

How to build a homemade sluice box. Hey Guys welcome back to my channel and today I’m going to show you how to build a homemade sluice box.

This page is full of useful information on how to build a sluice box out of wood. In this article, you will learn how to make a homemade sluice box with simple tools, as well as gain some more knowledge about this amazingly simple device.

How to build a sluice box out of wood

Sluice boxes are a great way to extract gold from your concentrates. They’re simple, low-cost and can be constructed in a variety of ways. The best part is that they are extremely effective at catching fine gold!

Building a sluice box is very easy and takes only a few hours. It’s one of the first things I learned when I started panning for gold several years ago because it’s such an easy way to separate out the finer particles of gold from your concentrates.

Two pieces of plywood (8 feet long x 5 feet wide) – one piece will be cut into two pieces, while the other will remain whole. You can use any kind of plywood you want as long as it isn’t too soft or brittle (like balsa wood). The thicker the better!

2-3 pieces of 2×4 lumber (cut into lengths between 4 feet and 6 feet)


Shovel/rake/paint brush

How to build a homemade sluice box

Building a sluice box is easy and inexpensive. You can make the wooden structure any size you want, but this article will show you how to build a small homemade sluice box that will be less than $15 in materials (including paint).

Sluice boxes are used for panning for gold or other precious metals. If you’ve ever watched an old western movie, then you’ve seen someone using one of these contraptions to try and find some gold.Wood sluice build - YouTube

The idea behind a sluice box is that it has a series of riffles that the water runs through. The riffles act like teeth, catching any gold in them and allowing it to drop out when you pull the sluice up from under water.

The sluice box is a simple device that uses gravity to separate gold from other materials. It consists of a wooden frame, with a screen or mesh at the bottom. The water flows into the top of the box, where it is slowed and allowed to pool. Gold particles sink to the bottom of the pool, while dirt and rocks remain at the top.

When building your own sluice box, there are several things you’ll need to consider:

The size of your sluice box will depend on how much material you plan on running through it at once, as well as how large an area you’ll be working in. If you’re only going to be panning for small amounts of gold, then a smaller sluice box will suffice; however, if you plan on using larger amounts of material or working in an area with more ground disturbance (such as near old mines), then a larger model would be more appropriate.

The size and shape of your homemade sluice box will also have an effect on how well it works. A rectangular box would work best because it offers more room for water flow than a square one; however, this design also means that there are more corners where water can get stuck and not move through properly

Sluice boxes are a great way to extract gold from your material. They can be made from all sorts of materials, but I prefer wood because it’s lightweight and durable.

Sluice boxes are basically a box with riffles on the bottom and sides, which allows water to flow through the box, picking up gold along the way.

Step 1: Gather Materials

You’ll need the following materials:

A base made of plywood or hardboard. You can buy a sheet of plywood at any home improvement store. If you don’t have access to a table saw, use a circular saw and a straightedge to cut the board down into smaller pieces that are 7 inches wide.

PVC pipe. Three-quarter-inch PVC pipe works well for this project, but anything between 3/4 inch and 1 inch in diameter should be fine.

A non-metallic screen material (mesh). A number of different materials can be used here, but we recommend using something like window screen or mosquito netting because it’s easy to obtain and won’t cost too much money.

Step 2: Cut Holes in the Base

The next step is to cut holes in the base so that water can flow through it. There are two ways to do this: drill holes with an electric drill or use a jigsaw (a handsaw with a fine blade). If you’re going to use an electric drill, make sure that you have plenty of drill bits on hand; they will dull quickly when cutting through wood. Using a jigsaw is easier than using a drill because it doesn’t

How to Build a Homemade Sluice Box for Fine Gold

A sluice box is an essential piece of equipment for any serious prospector. A sluice box will help you separate valuable mineral from the worthless dirt, rocks and other debris that often accompanies it. By using a sluice box, you can greatly increase your chances of finding gold or other precious metals.

Building a homemade sluice box is not difficult if you have the right tools and materials. The following steps will guide you through the process:

Step One – Choose Your Material

The first thing you need to do is choose which material you want to use for your homemade sluice box. You can choose wood or metal if these are available in your area, but plastic works well too. Wood is usually preferred because it’s cheaper than metal or plastic, but it can also be hard to find in some areas. Metal tends to be more expensive than wood, but it’s easier to cut and shape than wood is. Plastic has its own advantages and disadvantages as well – it’s easy to cut and shape but doesn’t hold up well over time or under extreme conditions such as rain or snow.

Step Two – Gather Your Tools

Next step is

A sluice box is an essential tool for prospecting and panning for gold. It is used to separate the heavier gold particles from the lighter materials in your stream or river. This homemade sluice box is easy to build, affordable and provides hours of fun!

What You’ll Need:

Two 2x4s cut into 4 ft pieces

One 2×4 cut into 2 ft pieces

One piece of plywood cut into 18 in x 48 in (or 3 ft x 1.5 ft)

Two hinges with screws

Wood glue

Step 1: Cut Your Pieces

The first step is cutting the two 2x4s down to 4 feet long. These will form the sides of the box. Next cut another 2×4 into two pieces that are each 2 feet long. These will be used for attaching the sluice box to rocks or stakes on either side of a stream or river. Finally, measure out two pieces of plywood that are 18 inches by 48 inches wide (or 3 feet by 1 ½ feet wide). You will use these as the bottom and top covers for your sluice box. Also make sure you have some wood glue handy as well as

I built my first sluice box out of an old couch, a couple of 2x4s and some PVC pipe. It worked great!

Mining for gold is not cheap. Even if you find it, you’ll have to pay to have it processed at a refinery and they will only give you a few dollars per ounce of gold. I found that building my own sluice box was much cheaper than buying one.

You can buy the parts for your homemade sluice box at any hardware store for about $80. Building it yourself will save you about $30 and allow you to customize it however you like.

To build your own sluice box:

Buy a 48-inch piece of 10-foot long 2×10 lumber (this will be the bottom frame). Also buy two 20-foot long 1×4 boards (these will be the sides). You may also need some other pieces of wood depending on how big or small you want your sluice box to be.

Cut your 2×10 into two 24 inch long pieces and two 12 inch long pieces (these are going to be used as rafters). Cut your 1×4 boards into four 20 inch long pieces and four 15 inch

The sluice box is an essential tool for gold prospecting. It’s a simple piece of equipment that can be built from scrap lumber and an old screen door. The best part is that it only takes a few hours to make one, and it costs less than $20.

Here are some tips for building your own homemade sluice box:57 DIY ideas | gold sluice, diy storage shed plans, gold sluice box

1) Look for old screen doors at thrift stores or garage sales. You want one that has a removable frame so you can get at the mesh.

2) Measure the length of your screen door and cut two pieces of wood about 2 feet longer than this measurement. You’ll want wood that’s sturdy enough to hold up under water pressure but light enough to move around easily when you’re prospecting.

3) Make sure the sides are square by measuring diagonally from corner to corner on both sides of each board (the distance between these points should be equal). Adjust if necessary by trimming one side slightly shorter than the other until they’re square with each other.

4) Cut out a notch at the top end of each board where you plan to attach them together with hinges so they’ll fold down flat when not in use. If

Here is a simple sluice box design that works great for small claims and the homemade prospector.

This sluice box is designed to handle any size of material from small gravel to large boulders. It can be used for panning or sluicing for placer gold.

The sluice box is built from common materials found at most hardware stores. It can be built in less than one hour using common tools such as a jigsaw, drill and screwdriver.

Materials needed:

1/4″ plywood – 1 piece 24″ x 48″ (for bottom)

1/4″ plywood – 1 piece 24″ x 48″ (for back)

2 pieces 1/4″ x 2x4x8′ (for sides)

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *