How to install porch railing on concrete

So I decided after three stumbles, to expand the width of my walkway by another two feet. I didn’t want to spend the full $1000 to have a contractor do it and so I began on digging in. Following the same basic steps as before, I placed the blocks along the side edge where the new walkway would be. After moving about fifty five bags of concrete this time, I not only was able to install it all but even rounded off the area for path (concrete is absolutely heavy when you struggle with bags of it). Here are some additional tips for anyone who might try to install something similarly:

This information is good for those who have a porch and are thinking of installing decorative concrete railing. Plastic or composite decking, aluminum, vinyl and cedar have the greatest resistance to rotting and fire. Wood railings are not suitable for exterior applications, especially when it means a gap of an inch between the rails.Stair Railing

How to install porch railing on concrete

If you want to add a little privacy to your deck or porch, adding a railing is an excellent way to do it. The best part about building your own railing is that you can make it any size or style that you want. If you’re looking for an easy DIY project, then this is a great place to start.

Here’s how to build porch railing with 2×4:


2×4 lumber

Screws (1 1/2 inches)

Nails (1 1/2 inches)


The most popular way to build a porch railing is with 2x4s. You can use 2x4s for the top and bottom rail, but you’ll want to use 2x6s for the middle posts. This gives the railing more stability, because it will be supported on both sides.

To install a porch railing on concrete, start by attaching the bottom rails to the concrete using masonry screws. These screws are made specifically for concrete and are meant to hold very well in this type of material.

Next, attach the tops of your posts to the top rails using lag bolts with washers on each side. Make sure these are placed into predrilled holes; otherwise, they’ll be very difficult to install and could crack your concrete. The exact size of these bolts will depend on what kind of rail you’re using (2×4 or 2×6) and how much weight it needs to hold up (100 pounds or 200 pounds).How to build a porch stair railing | HowToSpecialist - How to Build, Step  by Step DIY Plans

How to Install Porch Railing on Concrete

Build your own porch railing with this simple DIY tutorial. It’s an easy weekend project that requires little carpentry skill. Use these instructions to build a railing for your deck, porch or patio.

Step 1: Lay Out the Railing

Take a look at the space you want to enclose with your new railing. Measure the length and width of the area, then add 3 inches to each dimension. This will allow you to have enough room for the posts and rails without making them too close together (see Resources).

Step 2: Build Your Posts

Cut four 2-by-4s into 4-foot lengths with a handsaw or circular saw. Set one post over each corner of your railing frame to serve as corner posts, then attach them together by drilling pilot holes through each post into its adjacent partner and driving in three 3-inch deck screws per joint (see Resources).

Step 3: Attach Rails and Cap Them Off

You’ve already determined how tall you want your railings to be; now it’s time to build them. Cut eight more 2x4s into 4-foot lengths and cut them down so they’re all 48 inches long (see Resources). Attach them

Steps to building porch railing on concrete

Building a porch railing is not as difficult as you may think. The first step is to make sure that the concrete is level and has been treated with a sealant. If your porch is elevated by a set of steps, you should also make sure that they are level and sturdy.

Once your foundation is in place, it’s time to start building the railing itself. You can use either 2x4s or 1x4s for this project. If you’re using 2x4s, you’ll need to pre-drill holes for each screw so you don’t split the wood.

Once you have your lumber cut up into appropriate lengths, lay out the pieces as shown in the diagram above. This will ensure that all of your boards are even and fit together correctly once they are screwed down into place. Use 3″ deck screws to secure each board into place (or longer if needed).

Once all of your boards are secured into place, add a bottom rail on each side for added strength and stability (optional). Once this step is finished, fill any gaps between boards with spackle or caulking before finishing off with a top rail around the entire perimeter of your new porchHow To Add a Railing to a Stairway (Easy DIY Project) - YouTube

How to Build Porch Railing on Concrete

Building a porch railing on concrete is a great way to create an attractive and durable outdoor space. The project can be done in a weekend and requires minimal materials and tools. The steps involved are as follows:

Measure the length of the area you want to cover with the fence or railing. Add two feet to this measurement to determine how long your posts will need to be.

Dig holes for the posts at least 12 inches deeper than the measurement from Step 1. The deeper you dig, the more stable your posts will be.

Place concrete blocks in each hole and fill them with concrete mix until it reaches ground level (or slightly below). Leave about 3 inches of space between each block for drainage.

Set one post into each concrete block until it is level with the top of the blocks or just slightly below ground level (depending on how deep you dug). Use wood shims if necessary to make sure that each post is level with one another and placed in line with where they will be attached to one another later on.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *